I know it will have been asked/discussed before, I have looked but can't find it! I have two code readers but niether work on my 1999 US import (link error message appears). I'm now looking for a suitable reader/scanner that will cover and reset all the systems including the abs. Looking on...
hello there , im after a bit of advice regarding the back brake caliper on my 99 gt stang. I took the two front ones off and freed the pistons as they were both sticking. Decided to do the back ones aswell, took the drivers one off ,took out the pads and pressed pedal to get piston to come out a...
Hi All, Does anyone know where to get a genuine Service book? :-? I have a SN95 2003 Ford Mustang and didnt get a service book, but want to get one and start detialing regular services. Many thanks John T
Im away from the good book at the moment so can anyone tell me which diff oil to put in a '99GT? Thanks guys sorry its been asked before. Super Dragpack- im cracking open the diff after my MOT next week to see if its on its way out (we talked about it a while ago). What am i looking for roughly?...
Has anyone any experience of fitting and running with the roush side exhaust, noise levels ground clearance ect ect. I also have seen a Borla side exit system, so anyone with an Elanor or a Cervini?
On a recent trip to germany on the autobhan could only get my car upto 120mph. The car was very heavily loaded, but was only at about 3000rpm. This made me think is there a limiter on the top speed. How can I check if this is the case, and if so how can it be unlimited?
hi peeps i have the instructions for programming fobs onto the car, it says to look for a small connector block with 2 wires going to it in the boot on drivers side and short them together mine has a spare connector that side but it only has a single wire to one terminal any ideas ????
Ive been testing my TPS according to the manual but my TPS is wired up the opposite way round, can anyone check their wire colours?, mine is giving "ref" voltage on the top pin & "sig" voltage on the bottom pin, the manual says opposite????:confused: Brown+white-top=ref, Grey-middle=gnd, ...
Hi all Noticed some earlier thread on how to stop door chime, but were on a Fox. Any idea how to stop it on a 97 GT? Had a guy who done my remote locking, but said did not want to cut any wires. cheers (This is the irritating chime noise when door open,or reverse selected) Les
I have only had the car for 10 days and completed a 400 mile trip over 2 days with no problems. The low oil light has come on today. There are no signs of oil in the space I park, the dip stick shows at the bottom end. I am not sure when the oil was last changed as there is no service book, have...
I have a "squeak squeak squeak" noise coming from my car. Sounds like a fan belt or pulley squeak and it's constant (speed and volume) whether it's at idle or driving. Only time it stops is if you dip the clutch pedal about 1/2 inch then it stops completely until you come off the clutch again. ...
Does anyone know how to test MAF's on these cars, what pins + what readings etc, I think mine may be duff:-s
Does antbody know how to disconnect the really anoying warning bleeper (door open, keys in the ignition, reverse):mad: before it drives me mad:Angry please;) thanks:D
was talking to a friend today and we were on about petrol on what we use. we then got on about if a mustang is imported from japan will it have to run on super unleaded or not. as it might be remapped to use there fuel so it dont cause any damage. the reason i ask is mine is a jap import and has...
If I buy these from the USA......will they need beam benders on them for the UK laws and MOT? http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=360268198272&viewitem=&sspagename=STRK%3AMEWAX%3AIT
Hi, I'm trying to adjust a screen wash jet on a '96 Cobra so it washers the screen, not the scuttle. I'm used to the UK style, where you insert a pin and move the "eyeball" jet aimer, but there don't seem to be any movable parts - words of wisdom, please!
id like to replace the original tape player with something more modern is there an adapter to fit these connectors, not seen this type before
Hi, I have these S197 GT wheels on my SN95. The rears have 1inch spacers. No problem. The fronts currently have no spacers and although they look in-line with the rears, I need to space as they rub on the inside on full lock. Can anyone tell me What size spacer I should go for? Also if I put...
Well, thanks to brilliant engineering on new stone speed bumps in my development, my exhaust is broken yet again. This time, I need to replace the x-pipe as it is the source of my problems. Any places around here sell (affordable) x or h pipes? I'd rather not wait the time it will take to ship...
My engine is still pinking, I dont know what to do next, I have tried everything to stop it, High octane fuel, new O2 sensors, A SCT tuner, different Air filters, new vac pipes? what else & what could cause it?:-s Ive got no DTC's, I just need to get it sorted before the engine blows :-s
Hi all, i want to replace my stock 95 gt catback with a flowmaster american thunder system, can anyone tell me if there are flowmaster stockists in the u.k ?
Hello all, been a while since iv had time to post. Car has been off the road for two weeks since this happened, hopefully the mechanic can look at it today, but i wanted go get your opinions too:) Quick summary: I had to use the heaters for the first time in a while to clear the windows and...
Rang the guy in RMS Engineering to get my exhaust made. After taking some advice (thanks John) I`m going for a fail safe \m/cat back system. The guy was explaining about pipe diameters and I was wondering if there was a maximum diameter that should be used on my car regarding back pressure or the...
Im looking to buy a steeda short shifter direct from steeda, they have told me to use the silicone that they provide instead of a gasket. Anyone got a opinion on this? Cheers Jon.
Hi folks, Well my wife has been having a nosey around for ideas for my birthday and she's come across this: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=180536010136&viewitem=&sspagename=STRK%3AMEWAX%3AIT Now call me paranoid but I begin to seriously doubt any advert that...
There are currently 1 users browsing this forum. (0 members & 1 guests)
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
