Mustang insurance from Cherished Vehicle Insurance Services
Tab Content
  • rider's Avatar
    11-01-2019, 04:33 PM
    As well as the HP pump pressure it'd be worth checking out the O2 sensor. You can easily check out the integrity of the heater circuit by a simple...
    6 replies | 280 view(s)
  • rider's Avatar
    11-01-2019, 03:52 PM
    Found this into text on the system from 2006 for reference:
    6 replies | 280 view(s)
  • rider's Avatar
    11-01-2019, 02:04 PM
    Does sound fuel pressure related on a EFI system.
    6 replies | 280 view(s)
  • rider's Avatar
    01-01-2019, 08:22 PM
    My fastback got itself upgraded to a Sports GT by DVLA.
    42 replies | 4975 view(s)
  • rider's Avatar
    28-12-2018, 05:47 PM
    rider replied to a thread Timing/Carb tuning help in 64 to 73
    Your timing will be pretty good at 12deg. My 289 runs best at 10deg. For the carb you do need to set the two brass idle screws at the front of the...
    15 replies | 567 view(s)
  • rider's Avatar
    21-12-2018, 01:14 PM
    rider replied to a thread No Spark. 66' 289. in 64 to 73
    I'd be thinking stuck lifters, stuck closed. That'd normally give you a lot of play on the rocker when the valves are closed. Did you prime the...
    34 replies | 1396 view(s)
  • rider's Avatar
    19-12-2018, 11:45 PM
    rider replied to a thread No Spark. 66' 289. in 64 to 73
    Usually if it really wants to start but isn't quite managing it then I'd start with checking the standing battery is delivering 12.8V and above 11V...
    34 replies | 1396 view(s)
  • rider's Avatar
    19-12-2018, 06:05 PM
    rider replied to a thread Electrical Gremlins? in 64 to 73
    A good read, if you like good reads.
    6 replies | 314 view(s)
  • rider's Avatar
    13-12-2018, 02:46 PM
    rider replied to a thread No Spark. 66' 289. in 64 to 73
    You probably have a frazzled Petronix module then. If its the original I then its easily fried if you leave the ignition on for more than a few...
    34 replies | 1396 view(s)
  • rider's Avatar
    04-12-2018, 08:54 PM
    I did have an issue with a Rock order with a short ship that travelled via a Ron Fenton container so it didn't come to light for a few weeks. Then...
    4 replies | 1027 view(s)
  • rider's Avatar
    04-12-2018, 12:05 PM
    Spot on - thanks.
    2 replies | 197 view(s)
  • rider's Avatar
    04-12-2018, 10:57 AM
    Does anyone have a front wing panel lying around who could photograph the lower anchor point (where it bolts into the sill) for me and post it here...
    2 replies | 197 view(s)
  • rider's Avatar
    04-12-2018, 10:35 AM
    rider replied to a thread Brake bias 67 289 in 64 to 73
    The rears are adjustable and should be auto adjusting if they are working properly. A squeak when engaging drive, what makes you think its brake...
    3 replies | 263 view(s)
  • rider's Avatar
    02-12-2018, 04:35 PM
    For modern seats available in Europe it seems MX5 or MGF are the ones to go for though they don't fold forward being out of a two seater. There are...
    6 replies | 368 view(s)
  • rider's Avatar
    29-11-2018, 05:42 PM
    On my variable timing light there is a dial that you adjust to correspond to the number of cylinders (effectively firings per cycle). If you haven't...
    4 replies | 277 view(s)
  • rider's Avatar
    27-11-2018, 01:08 PM
    rider replied to a thread 390 recommended fuel ? in 64 to 73
    You can cope with lower RON fuels by retarding the ignition, people (I assume people who have data available) suggest 4 degrees retardation if going...
    20 replies | 1078 view(s)
  • rider's Avatar
    26-11-2018, 01:01 PM
    rider replied to a thread 390 recommended fuel ? in 64 to 73
    5 star, but that went a long time ago. I use premium unleaded 97 RON and then add in a lead replacement additive that raises the RON to 99. Shell do...
    20 replies | 1078 view(s)
  • rider's Avatar
    16-11-2018, 04:01 PM
    rider replied to a thread 1964 mustang wiring in 64 to 73
    In these instances usually the internet is your best friend.
    13 replies | 662 view(s)
  • rider's Avatar
    13-11-2018, 11:43 AM
    MIG welders come in two guises, gas or flux wire. For hobby use may as well go for the flux wire as that saves you a consumable gas cylinder....
    8 replies | 492 view(s)
  • rider's Avatar
    11-11-2018, 08:43 PM
    It depends how quickly you want the parts. Summit Racing do all things Mustang and usually do heavily discounted air shipping rates at some point...
    7 replies | 502 view(s)
  • rider's Avatar
    02-11-2018, 02:30 PM
    rider replied to a thread NEC November 2018 in Shows and Cruises
    I have exhibited at the NEC before so I am very familiar with the Thursday to Sunday evening routine and found the 4 days flew by very quickly....
    17 replies | 3322 view(s)
  • rider's Avatar
    02-11-2018, 01:31 PM
    rider replied to a thread Under bonnet insulation in 64 to 73
    I fitted under bonnet insulation to my MGB last year that was apparently a factory fit option. Didn't make any discernible noise difference but did...
    2 replies | 283 view(s)
  • rider's Avatar
    30-10-2018, 02:48 PM
    rider replied to a thread NEC November 2018 in Shows and Cruises
    Taking time out to read through archive NEC threads its a recurring theme of no one knows what goes on with this event and no one will ever know...
    17 replies | 3322 view(s)
  • rider's Avatar
    30-10-2018, 11:15 AM
    rider replied to a thread NEC November 2018 in Shows and Cruises
    As this is an event very much in the near future it'd be nice to hear from Chris himself on what is happening. What cars are going to be on stand....
    17 replies | 3322 view(s)
No More Results
About rider

Basic Information

About rider
Membership:
6432

Statistics


Total Posts
Total Posts
482
Posts Per Day
0.39
General Information
Last Activity
18-01-2019 08:33 PM
Join Date
02-09-2015